Skip to content

The first cold front is a lousy time to find out your heater won’t start. You’ve pulled out the blankets, switched the thermostat, and now the vents aren’t giving you much. Our advice? Give the equipment a trial run before you need it. Here’s how to prepare your heating system for winter, including the checks you can handle and the work we recommend leaving to a technician.

Test Your Heat and Check the Thermostat

Choose a mild day when you can stay home while the system runs. Set the thermostat to Heat, raise the temperature a few degrees above the room temperature, and give the equipment time to start. Setting it much higher won’t heat the house faster.

Check that air reaches the rooms and the indoor temperature begins rising. A heat pump’s supply air may feel less hot than a gas furnace’s, so judge it by its ability to warm the home rather than expecting the same vent temperature.

While you’re at the thermostat:

  • Replace batteries if your model uses them and they’re due.
  • Review programmed schedules left over from cooling season.
  • Check that the fan setting matches the equipment’s instructions. Auto is a common setting for normal operation.

A brief dusty odor can occur when heating starts after months of inactivity. A persistent burning smell, burning-plastic odor, or loud banging needs attention. Shut the system off and arrange heating repair rather than repeatedly restarting it.

If you smell gas, leave the home immediately. Do not operate switches or use a phone inside. Call your gas utility’s emergency line or 911 from a safe location outside.

Check the Air Filter and Clear Indoor Vents

After a long Houston cooling season, don’t assume the filter is ready for winter. Heating and cooling commonly use the same filter and ductwork.

With the system off, inspect the filter and replace it if dirty or due under its recommended schedule. Match the required size and airflow direction. If you want to change filter types, check equipment compatibility first; a more restrictive filter can cause airflow problems.

Walk through the house and move furniture, rugs, and stored items away from supply registers and return grilles. Keep registers open unless your system was specifically designed for a different arrangement.

Also clear storage away from the furnace or air handler. Paint, cleaning chemicals, cardboard, and other household items do not belong against heating equipment. Follow the manufacturer’s clearance requirements.

Clear Debris Around Your Outdoor Heat Pump

This step applies if your home uses a heat pump. Unlike an outdoor AC condenser paired with a furnace, a heat pump’s outdoor unit operates during heating season.

Remove loose leaves and yard debris around the cabinet, and maintain the manufacturer’s required space around it. Do not wrap or cover a heat pump that needs to run.

During cold, damp weather, a light coating of frost can form on the outdoor coil. The system’s defrost cycle normally removes it, and you may see steam during that process. Thick ice that remains or keeps building up deserves an inspection. Do not chip it away or pour hot water over the equipment.

Test Your Carbon Monoxide Alarms

If your home has a gas furnace or other fuel-burning equipment, working carbon monoxide alarms belong on your winter checklist. Carbon monoxide has no smell, so you cannot rely on your nose to detect it.

The Consumer Product Safety Commission recommends carbon monoxide alarms on every floor and outside sleeping areas. Test them monthly, and follow each alarm’s instructions for battery replacement, placement, and expiration dates.

If a CO alarm sounds, get everyone outside immediately and call 911. Do not stay inside to find the source.

An electric furnace or heat pump does not produce carbon monoxide through combustion, but other appliances, an attached garage, or a generator can still create a risk.

Schedule Professional Heating Maintenance

A successful test run tells you the heater starts. It does not tell you the heat exchanger, electrical components, or safety controls are in good condition.

That’s why it’s a good idea to schedule heating maintenance before cold weather settles in. At Cold Air Pros, inspections depend on the equipment in your home. Our heating maintenance includes checks of:

  • Gas furnace safety: Heat exchanger condition and possible carbon monoxide risks
  • Electrical components: Connections, controls, signs of wear
  • Operating sequence: Startup, heating operation, shutdown
  • System condition: Performance concerns and parts that may need repair

We explain what we find and recommend repairs based on the equipment’s condition. A furnace and a heat pump need different checks, so the service should reflect the system you actually have.

For a broader view of seasonal service, our guide to what HVAC maintenance includes explains how maintenance differs from a repair visit.

Get Your Heat Ready with Cold Air Pros

Houston weather doesn’t always give you much time between short sleeves and reaching for the thermostat. Get the heater checked while leaving it off for a repair is still an inconvenience you can plan around.

At Cold Air Pros, we help homeowners prepare furnaces and heat pumps for colder weather. Our HVAC maintenance plans can help you stay on schedule with seasonal service. Contact our team to schedule your heating tune-up.

If your AC coil looks dirty, you might be tempted to grab the hose and rinse it off. Sometimes that’s a reasonable place to start, but we recommend following a few additional steps first. Knowing how to clean AC coils starts with identifying which coil you’re dealing with and what your equipment’s manufacturer allows.

Which AC Coil Are You Cleaning?

The average central air conditioner has two coils:

  • The outdoor condenser coil releases heat collected inside your home. Dirt, leaves, and grass clippings can collect on its surfaces and restrict airflow.
  • The indoor evaporator coil absorbs heat from indoor air. It sits inside the air handler or near the furnace, where dust can accumulate if filtration is poor.

Both coils need clean surfaces to transfer heat effectively. Cleaning the outdoor unit will not remove buildup on the indoor coil.

How to Clean Outdoor AC Condenser Coils

These steps apply to basic exterior cleaning of an accessible outdoor coil. Check your equipment manual first. Coil designs and approved cleaning methods vary.

1. Shut Off Power

Turn the thermostat off, then disconnect power using the equipment’s designated disconnect or breaker according to the manufacturer’s instructions. Turning the thermostat off alone does not isolate electrical power.

If you can’t confidently identify the correct power shutoff, leave the cleaning to a technician. Do not open electrical compartments.

2. Clear the Area Around the Unit

Remove loose leaves, twigs, and grass clippings around the cabinet. Wear gloves and keep your hands away from sharp fins.

Pay attention to the space between the unit and the house (debris can collect where it is harder to see). Trim nearby vegetation to the clearance specified by the equipment manufacturer, and direct mower discharge away from the unit.

3. Gently Rinse Accessible Coil Surfaces

If the manufacturer permits it, use a garden hose with a gentle stream to rinse accessible outdoor coil surfaces. Keep water away from electrical compartments and connections.

Do not use a pressure washer or a concentrated jet. The thin fins can bend, restricting the airflow you are trying to restore.

Leave cabinet panels, protective guards, and the fan assembly in place. If they prevent access to the dirty area, schedule professional AC maintenance rather than taking the unit apart.

4. Skip Unapproved Cleaners

Water may be enough for loose surface dirt. Stubborn buildup needs a cleaning method approved for that particular coil.

Do not assume a bottle labeled “coil cleaner” is compatible with every system. Coil material, coatings, dilution, contact time, and rinsing requirements all affect the choice. Avoid household cleaners and aggressive scrubbing.

5. Follow the Restart Instructions

Allow the equipment to drain and dry as directed by the manufacturer before restoring power. Put the hose and tools away, then restart the system according to its instructions.

If cooling remains poor, repeated washing is not the next step. An AC repair inspection can identify problems that cleaning cannot fix.

How Are Indoor Evaporator Coils Cleaned?

We recommend professional cleaning for indoor evaporator coils. Access can involve working around wiring, insulation, delicate fins, and the condensate system.

A technician will inspect the coil, select an approved cleaning method, and protect surrounding components. Depending on access and buildup, cleaning may involve removing surface debris and applying a compatible cleaner. Any required rinsing must be controlled so water and loosened dirt do not overflow the drain pan.

The drain deserves attention during this work. Washing debris into a restricted drain can create another problem. Our guide to why air conditioners leak water explains how drainage issues and frozen coils can lead to indoor leaks.

How Often Should AC Coils Be Cleaned?

You should have coils inspected during annual maintenance and cleaned when their condition calls for it. The U.S. Department of Energy recommends checking the evaporator coil every year and cleaning it as needed.

For Houston homeowners, a useful habit is checking the outdoor unit after mowing, landscaping work, or nearby construction. Visible buildup may need attention before the next scheduled visit. Indoor cleaning frequency depends more on filtration, equipment condition, and the inspection findings.

Coil inspection is one part of a maintenance visit. Our article on what HVAC maintenance includes explains the other checks involved.

Can Dirty Coils Cause Cooling Problems?

Yes, buildup can interfere with airflow and heat transfer, reducing cooling performance and increasing runtime. A heavily restricted indoor coil can also contribute to freezing.

Those symptoms do not prove the coil is dirty though. A clogged filter, blower problem, or refrigerant issue can produce similar complaints. If you see ice, turn cooling off and arrange an inspection. Do not chip it away or try to clean a frozen coil.

Let Cold Air Pros Handle Your Next AC Tune-Up

You shouldn’t have to spend your weekend taking an air conditioner. Clear away yard debris, follow your equipment’s care instructions, and let us handle the cleaning that requires opening the system!

At Cold Air Pros, we help Houston homeowners maintain and repair their cooling equipment. Our HVAC maintenance plans make it easier to stay on schedule with routine service, and we provide new AC installation when it’s time to replace old equipment. Contact our team or call (713) 476-0429 to schedule service.

If you’re asking, “Why is my air conditioner leaking water?” there are a few places we’d start. The condensate drain may be clogged, the evaporator coil could be frozen, or the drain pan may be damaged. It could also be a condensate pump or installation problem. The leak may not look serious at first, but water can spread into drywall, insulation, flooring, and nearby electrical components while the system’s running.

Where Does the Water Come From?

Your air conditioner removes heat and moisture from indoor air. Moisture collects on the cold evaporator coil, drips into a drain pan, and exits through the condensate drain line.

Houston air conditioners may remove a lot of moisture during hot, humid weather. That means more water moving through the drainage system and more opportunity for buildup or drainage problems.

Water outside near the condensate drain may be normal. Water around the indoor unit, coming through a ceiling, or collecting near a vent is not.

1. The Condensate Drain is Clogged

Cause: This is one of the first things we check when an AC is leaking water. The drain line stays wet during the cooling season, so algae, dirt, and other buildup can collect inside and eventually block it. Once the water has nowhere to go, it backs up into the pan and may spill around the indoor unit.

Solution: The line needs to be cleared, but we also want to check the pan, fittings, and where the line drains outside. If the AC stopped running around the same time the leak appeared, the float switch may have shut the system down before the pan overflowed.

2. The Evaporator Coil Froze

Cause: A frozen coil usually means the system has an airflow or refrigerant problem. It could be a dirty filter, blocked return, dirty coil, blower issue, or low refrigerant. Then the ice starts melting and you end up with more water than the drain pan can manage.

Solution: Shut off the cooling and let the ice thaw. You can check the filter while the system’s off, but changing it may not solve the actual problem. If the coil freezes again or the airflow still feels weak, it’s time to have the system inspected.

3. The Drain Pan is Cracked or Rusted

Cause: The drain pan sits below the evaporator coil and catches water as it drips off. Metal pans can rust through over time, and plastic pans sometimes crack or move out of position. Once that happens, the water may leak before it ever reaches the drain line.

Solution: A damaged pan usually needs to be replaced. Some systems also have a secondary pan below the air handler, especially when the equipment is in an attic. Both pans should be checked because the water you see may have already passed through the main pan.

4. The Drain Line is Damaged or Installed Incorrectly

Cause: A drain line can come loose at a connection, crack, or sag enough to hold water. It also needs the right slope so condensation can keep moving toward the drain. If the pitch, trap, or venting is wrong, backups may keep happening even after someone clears the line.

Solution: The line may need to be reconnected, repaired, or rerouted. This is worth checking if the AC has leaked more than once and drain cleaning only seems to fix it for a short time.

5. The Condensate Pump Stopped Working

Cause: Some systems cannot move condensate outside using gravity alone, so they have a small pump that collects and removes the water. If the motor fails, the float sticks, or the discharge tube becomes blocked, the reservoir can overflow.

Solution: The pump and tubing need to be inspected. Sometimes buildup can be cleaned out, but a failed pump will have to be replaced. Shut the system off if water is getting close to the pump wiring or other electrical components.

6. The Equipment or Ductwork is Sweating

Cause: Not every puddle comes from the drain system. Moisture can collect on the outside of an air handler, refrigerant line, duct, or supply vent when humid air reaches a cold surface. We see this with missing insulation, air leaks around vents, high indoor humidity, or ductwork running through a hot attic.

Solution: Replacing damaged insulation may help, but that is not always the whole repair. The technician may also need to check airflow, duct leakage, indoor humidity, and gaps around the vent. If you only dry the area or replace the insulation without finding the reason it got wet, the moisture will probably return.

What Should You Do When Your AC Is Leaking?

A small amount of water can spread farther than it looks, especially when the air handler is above a ceiling. Turn off the system if water is actively spreading, coming through drywall, or getting close to electrical equipment.

You can safely do a few basic checks…

  • Look at the air filter and replace it if it is dirty.
  • Check for visible ice on the refrigerant line or indoor unit.
  • Move furniture and other belongings away from the leak.
  • Use towels or a container to limit water damage.
  • Check the outdoor end of the drain line for an obvious blockage.

Do not remove equipment panels or try to handle refrigerant components yourself. Pouring harsh drain-cleaning chemicals into the line can also damage HVAC components or create a safety problem for the technician working on it later.

Call for HVAC service if the AC is not cooling, the coil is frozen, the drain pan is overflowing, or the water returns after cleanup.

Stop the AC Leak Before it Spreads!

Finding water near the AC does not tell you the full problem. Cold Air Pros can inspect the coil, drain line, drain pan, airflow, and condensate pump to find where the water is coming from and why. Schedule air conditioner repair if your system is leaking, freezing, or no longer cooling correctly. Regular air conditioner maintenance can also help catch drain buildup and worn components before they leave water around the indoor unit.

Contact Cold Air Pros to schedule AC service in Houston or a surrounding community.

If you schedule HVAC maintenance every year, you probably want to know what you’re actually paying a technician to do. So, what does HVAC maintenance include? A typical visit involves inspecting, cleaning, and testing the system, but the exact work depends on your equipment, its condition, and the maintenance plan you have.

What’s Included in HVAC Maintenance?

There’s a lot more to HVAC maintenance than changing the air filter and making sure the system turns on. A technician checks how the equipment is actually running and looks for wear, airflow problems, electrical issues, and other conditions that could affect performance.

Maintenance AreaWhat is CheckedWhat it Can Indicate
Airflow and filtrationFilter condition, airflow, and visible restrictionsRestricted airflow can reduce system performance and cause equipment to work harder than necessary.
Electrical componentsConnections, wiring, capacitors, contactors, and controls as applicableLoose connections, heat damage, and worn electrical components can lead to intermittent operation or component failure.
Cooling componentsIndoor and outdoor coils, condensate drainage, and general cooling operationDirty heat transfer surfaces and drainage problems can affect cooling performance or cause water issues.
Refrigerant performanceOperating temperatures and pressures as appropriate for the systemReadings outside the expected range can point to airflow, refrigerant, or equipment problems that require further diagnosis.
Heating componentsIgnition, burners, heat exchanger, and safety controls as applicableHeating equipment requires system-specific operating and safety checks, particularly for combustion equipment.
Thermostat and controlsThermostat response, settings, and communication with the equipmentThe system cannot operate correctly if controls are not properly calling for heating or cooling.
Overall equipment conditionLeaks, unusual noises, vibration, corrosion, and visible wearPhysical signs can provide early clues that a component is deteriorating or the system is operating abnormally.

AC vs. Heating Maintenance: What Changes?

Not every HVAC system needs the exact same maintenance. What a technician checks depends on the equipment and whether it’s being used for cooling or heating.

During AC maintenance, technicians focus on heat transfer, condensate drainage, refrigerant operation, and the indoor and outdoor cooling components. A dirty coil, restricted airflow, or clogged drain can cause trouble even when the AC still seems to be running normally.

Gas furnaces require a different approach. Ignition, burners, venting, the heat exchanger, and safety controls all need to be checked because the system burns fuel to produce heat.

Heat pumps work differently from furnaces. They use a refrigeration cycle for both cooling and heating, reversing the direction of heat transfer in heating mode. That means maintenance needs to account for components that work during both seasons.

Does HVAC Maintenance include Repairs?

Maintenance and repair are two different things. An HVAC maintenance visit may include cleaning, testing, inspections, and routine adjustments, but finding a problem doesn’t necessarily mean the repair itself is included. If a technician finds a failing part, drainage issue, or another problem, additional work may be needed to correct it. Check your HVAC maintenance plan for the specific services and benefits included.

How Often Should HVAC Maintenance Be Done?

A good time to schedule HVAC maintenance is before your equipment heads into its busiest season. That usually means checking the AC before the hotter months and the heating system before temperatures drop.

Here in Houston, AC systems work especially hard through long stretches of hot, humid weather. That extra runtime can make regular maintenance more important. The age and condition of your equipment, how often it runs, and the manufacturer’s recommendations should also factor into your maintenance schedule.

How Often Should HVAC Maintenance Be Done?

A good time to schedule HVAC maintenance is before your equipment heads into its busiest season. That usually means checking the AC before the hotter months and the heating system before temperatures drop.

Here in Houston, AC systems work especially hard through long stretches of hot, humid weather. That extra runtime can make regular maintenance more important. The age and condition of your equipment, how often it runs, and the manufacturer’s recommendations should also factor into your maintenance schedule.

It’s also worth checking the maintenance requirements in your equipment warranty. Many manufacturers require regular maintenance or may exclude repairs when a failure is tied to improper maintenance. Keeping service records can also help if you need to make a warranty claim later.

Keep in mind that air filters are on a much shorter schedule. Filter type, pets, indoor conditions, and how often the system runs can all affect how frequently yours needs to be changed.

Get Started with HVAC Maintenance with Cold Air Pros

Houston weather puts plenty of hours on your HVAC system, especially during the cooling season. Cold Air Pros can check how your system is operating, catch signs of trouble, and take care of the maintenance your equipment needs.

Schedule HVAC maintenance with Cold Air Pros or compare our maintenance plans to find the right option for your home.